A frame is a digital data transmission unit in computer networking and telecommunications. In packet switched systems, a frame is a simple container for a single network packet. In other telecommunications systems, a frame is a repeating structure supporting time-division multiplexing. A frame typically includes frame synchronization features consisting of a sequence of bits or symbols that indicate to the receiver the beginning and end of the payload data within the stream of symbols or bits it receives. If a receiver is connected to the system during frame transmission, it ignores the data until it detects a new frame synchronization sequence. == Packet switching == In the OSI model of computer networking, a frame is the protocol data unit at the data link layer. Frames are the result of the final layer of encapsulation before the data is transmitted over the physical layer. A frame is "the unit of transmission in a link layer protocol, and consists of a link layer header followed by a packet." Each frame is separated from the next by an interframe gap. A frame is a series of bits generally composed of frame synchronization bits, the packet payload, and a frame check sequence. Examples are Ethernet frames, Wi-Fi frames, 4G frames, Point-to-Point Protocol (PPP) frames, Fibre Channel frames, and V.42 modem frames. Often, frames of several different sizes are nested inside each other. For example, when using Point-to-Point Protocol (PPP) over asynchronous serial communication, the eight bits of each individual byte are framed by start and stop bits, the payload data bytes in a network packet are framed by the header and footer, and several packets can be framed with frame boundary octets. == Time-division multiplex == In telecommunications, specifically in time-division multiplex (TDM) and time-division multiple access (TDMA) variants, a frame is a cyclically repeated data block that consists of a fixed number of time slots, one for each logical TDM channel or TDMA transmitter. In this context, a frame is typically an entity at the physical layer. TDM application examples are SONET/SDH and the ISDN circuit-switched B-channel, while TDMA examples are Circuit Switched Data used in early cellular voice services. The frame is also an entity for time-division duplex, where the mobile terminal may transmit during some time slots and receive during others.
Grokking (machine learning)
In machine learning, grokking, or delayed generalization, is a phenomenon observed in some settings where a model abruptly transitions from overfitting (performing well only on training data) to generalizing (performing well on both training and test data), after many training iterations with little or no improvement on the held-out data. This contrasts with what is typically observed in machine learning, where generalization occurs gradually alongside improved performance on training data. == Origin == Grokking was introduced by OpenAI researcher Alethea Power and colleagues in the January 2022 paper "Grokking: Generalization Beyond Overfitting on Small Algorithmic Datasets". It is derived from the word grok coined by Robert Heinlein in his novel Stranger in a Strange Land. In ML research, "grokking" is not used as a synonym for "generalization"; rather, it names a sometimes-observed delayed‑generalization training phenomenon in which training and held‑out performance do not improve in tandem, and in which held‑out performance rises abruptly later. Authors also analyze the "grokking time", the epoch or step at which this transition occurs in those scenarios. == Interpretations == Grokking can be understood as a phase transition during the training process. In particular, recent work has shown that grokking may be due to a complexity phase transition in the model during training. While grokking has been thought of as largely a phenomenon of relatively shallow models, grokking has been observed in deep neural networks and non-neural models and is the subject of active research. One potential explanation is that the weight decay (a component of the loss function that penalizes higher values of the neural network parameters, also called regularization) slightly favors the general solution that involves lower weight values, but that is also harder to find. According to Neel Nanda, the process of learning the general solution may be gradual, even though the transition to the general solution occurs more suddenly later. Recent theories have hypothesized that grokking occurs when neural networks transition from a "lazy training" regime where the weights do not deviate far from initialization, to a "rich" regime where weights abruptly begin to move in task-relevant directions. Follow-up empirical and theoretical work has accumulated evidence in support of this perspective, and it offers a unifying view of earlier work as the transition from lazy to rich training dynamics is known to arise from properties of adaptive optimizers, weight decay, initial parameter weight norm, and more. This perspective is complementary to a unifying "pattern learning speeds" framework that links grokking and double descent; within this view, delayed generalization can arise across training time ("epoch‑wise") or across model size ("model‑wise"), and the authors report "model‑wise grokking".
CEITON
CEITON is a web-based software system for facilitating and automating business processes such as planning, scheduling, and payroll using workflow technologies. The system is used by several media companies such as MDR, Yle, RAI and Red Bull Media House. In December 2018, the first CEITON User Group Meeting took place in Leipzig, Germany. == Architecture == The software runs on a server (on premises) or in the cloud and is scalable on parallel servers. Data security is warranted by role-based access control (RBAC). The software is used via web-browsers and not dependent on particular system software. == Structure and Features == CEITON combines the two classical approaches of production planning and control and workflow management. === Project Management === The scheduling system plans, manages, bills, and analyzes projects or tasks. It manages human and technical resources, material, and locations on a single GUI. The system uses a gantt chart to assign tasks to be done to available and eligible resources (i.e. staff), automatically or by drag-and-drop. The scheduling module includes material management, resource management/ human resource management, integration of freelancers, clients and suppliers, long-term budget planning, time-tracking, shift scheduling, quality management, delivery and logistics, document management, archive, analysis and controlling, business reporting, as well as all accounting and documentation processes. === Workflow === The workflow management system module coordinates business processes. Processes are defined once as a workflow and then repeatedly executed. Human resources are automatically assigned to steps (tasks) and integrated in workflow forms. Systems are integrated with an EAI/SOAP module, allowing data exchange with arbitrary external systems which are also involved in the business process. It also features a 3-D workflow overview in which the status of each project step can be determined by its color in the overview. === Process Management === For project and order processing management, business processes are designed as workflows, and coordinate communication automatically. Different user interfaces for staff, customers or suppliers can be created so each gets only relevant information. Different workflow forms are associated with different log-ins. The main application for the system is knowledge-based business processes, in which many people are involved and virtual results are produced, e.g. in research, or development of media products, such as TV and movies. Broadcasters and media companies such as MDR and Yle use CEITON to control their production processes for products and services and coordinate complex workflows with all kinds of resources. === Integrations === An integrated EAI module allows CEITON to integrate every external system in any business process without programming, using SOAP and similar technologies. Aspera and FileCatalyst were integrated for faster data transfer, yet complex ERP systems and numerous SAP modules have also been integrated, for example, to extract working times to payroll. === Mobile Working === Since Version 7, released in 2015, CEITON includes a time-tracking module allowing employees to enter their times from mobile devices such as tablets running Android, iPhones etc. == History == Ceiton Technologies (SME tech firm), the company developing CEITON, was founded in Leipzig, Germany in 2000, staffing solutions for the Bureau of Internal Revenue in Manila, Philippines, were implemented in 2000 together with the Deutsche Gesellschaft für Technische Zusammenarbeit of the German government. The first version (1.0) of the software was released in July 2001. The product was originally developed for German broadcasting companies. CEITON is named after the Japanese concept Seiton, one of the principles of Japanese workplace design methodology known as 5S. Since version 7, released in 2015, CEITON includes a time-tracking module allowing employees to enter their times from mobile devices such as tablets running Android, iPhones etc. In May 2005 CEITON won the IQ innovation award, sponsored by Siemens, in the category Excellent innovation in the IT-sector. Since 2007, CEITON has been present at the broadcast trade fairs NAB in Las Vegas and IBC in Amsterdam. In 2020, the company celebrated its 20th anniversary.
CAMeL-View TestRig
CAMeL-View is a software application, which is used for the model based design of mechatronic systems (multi-body simulation, block diagrams, pneumatic systems, hydraulic systems, general simulation, linear analysis and Hardware-in-the-Loop). CAMeL-View enables object-oriented model creation of mechatronic systems through the use of graphic blocks. The basic elements of multi-body system dynamics, control technology, hydraulics and hardware connectivity support the modeling process. The user’s proprietary C-Code can also be integrated into the models, which allows CAMeL-View TestRig to be implemented in all phases of the model based design process ( modeling, physical testing and prototyping), and lends itself especially well to mechatronic system design. The model’s structure is described and displayed with the help of directional connectors. Physical connections (such as mechanical or hydraulic linkages) as well as input and output connections (signal flow) are also available. The input of equations is done via mathematical expressions, e.g. the input of constitutive differential equations in vector and matrix form. Based on the model’s structure, the descriptive equations are converted into non-linear state space representations and converted into executable C-Code. CAMeL-View supports the simulation process with a configurable “experiment environment” (for simulator and instrumentation components) which allows the user to apply simulation models to supported targets (MPC5200, TriCore, X86, etc.) without the need for additional software tools for Hardware-in-the-Loop applications. In addition, the generation of so-called S-Functions for use in Simulink and the generation of ANSI C-Code for use in stand-alone simulators is also supported. A particularly noteworthy feature in CAMeL-View TestRig is the way in which the descriptive equations for multi-body system models are created. All multi-body simulation formalisms used for code generation create their equations in the form of typical explicit differential equations (ODE). This is especially important in Hardware-in-the-Loop applications where the calculation of simulation results within a specific, defined time frame must be assured. Only then is it possible to implement complex multi-body simulation models for Hardware-in-the-Loop applications under stringent real-time conditions. These constraints cannot be met when using DAE-based methods. Additional Toolboxes are available for linear analysis (Eigenvalues, pole-zero analysis, frequency response, etc.) of VRML-based animation. Development of CAMeL-View began in 1991 in the Paderborn Mechatronic Laboratory of Professor Dr. Ing. J. Lückel. The software was based on predecessors that had been developed there since 1986. The name stands for Computer Aided Mechatronic Laboratory – Virtual Engineering Workbench and describes the basic intent of one of the specific demands placed on development engineers in the computer lab.
FreshBooks
FreshBooks is accounting software operated by 2ndSite Inc. primarily for small and medium-sized businesses. It is a web-based software as a service (SaaS) model, that can be accessed through a desktop or mobile device. The company was founded in 2003 and is based in Toronto, Canada. == History == FreshBooks was founded in 2004 by Mike McDerment, Levi Cooperman, and Joe Sawada in Toronto, Ontario. McDerment incorporated a second company, BillSpring in January 2015 to work on new product development. It was rolled back into FreshBooks as an updated interface in 2016. Initially FreshBooks functioned like an electronic invoicing program targeting IT professionals. After the release of the new interface, the initial release of FreshBooks was referred to as "FreshBooks Classic." FreshBooks Classic was discontinued in 2022 after migrating users to the new platform. FreshBooks Classic's front-end application was built in PHP, and the backend services were built in Python while the new FreshBooks uses the same backend services with a JavaScript single-page application. == Product == FreshBooks is a subscription-based accounting software platform that provides features such as invoicing, accounts payable, expense and time tracking, retainers, fixed asset depreciation, purchase orders, payroll integrations, mileage tracking, double-entry accounting, and standard business reporting. Financial data is stored in the cloud on a unified ledger, enabling access from desktop and mobile devices. The platform includes a free API for integration with external applications and supports multiple tax rates and currencies. It also offers project management and payroll functionalities. Pricing is based on a recurring monthly fee. FreshBooks supports country-specific tax calculations, including GST and HST in Canada, sales taxes in the United States, and MTD compliance in the UK. == Operations == FreshBooks has its headquarters in Toronto, Canada with operations in North America, Europe and Australia. Founder Mike McDerment was the chief executive officer of the company from 2003 until 2021, when he stepped down and was replaced by Don Epperson, but stayed as the executive chair. Don Epperson had previously joined FreshBooks as executive director in 2019. == Funding == FreshBooks was initially self-funded. In 2014, the company raised a Series A venture investment of $30 million led by the venture capital firm Oak Investment Partners, with participation by Georgian Partners and Atlas Venture. In 2017, FreshBooks announced that it raised another $43 million in funding from Accomplice, Georgian Partners and Oak Investment Partners. On August 10, 2021, FreshBooks announced that it had secured $80.75 million in Series E funding and $50 million in debt financing. FreshBooks also reached a valuation of more than $1 billion.
Tapingo
Tapingo was an American mobile commerce application that offers advance ordering for pickup and food delivery services for college campuses. The company was acquired by Grubhub in September 2018 for approximately $150 million. Following the acquisition, Tapingo’s campus-ordering functionality was integrated into the Grubhub app (Grubhub Campus Dining) and the Tapingo service was discontinued during 2019. Tapingo is differentiated from other on-demand delivery/logistics companies, such as Waiter.com, Postmates, or DoorDash, by focusing its efforts on serving the college market. Through Tapingo, users can browse menus, place orders, pay for the meal and schedule the pickup or have it delivered. On certain campuses, students are able to use their university's meal dollars to pay for food. In the spring of 2012, Tapingo first launched its services on five campuses (Santa Clara University, Loyola Marymount University, Biola University, the University of Maine, and California Lutheran University), and has since expanded to more than 200 college campuses across the U.S. and Canada, serving 100 markets. To date, Tapingo has received venture funding from Carmel Ventures, Khosla Ventures, Kinzon Capital, DCM Ventures and Qualcomm Ventures. In fall 2015, Tapingo announced expansion plans through major partnership deals with national brands like Chipotle Mexican Grill and 7-Eleven, regional restaurants such as Taco Bueno, and global foodservice provider Aramark.
Linux Trace Toolkit
The Linux Trace Toolkit (LTT) is a set of tools that is designed to log program execution details from a patched Linux kernel and then perform various analyses on them, using console-based and graphical tools. LTT has been mostly superseded by its successor LTTng (Linux Trace Toolkit Next Generation). LTT allows the user to see in-depth information about the processes that were running during the trace period, including when context switches occurred, how long the processes were blocked for, and how much time the processes spent executing vs. how much time the processes were blocked. The data is logged to a text file and various console-based and graphical (GTK+) tools are provided for interpreting that data. In order to do data collection, LTT requires a patched Linux kernel. The authors of LTT claim that the performance hit for a patched kernel compared to a regular kernel is minimal; Their testing has reportedly shown that this is less than 2.5% on a "normal use" system (measured using batches of kernel makes) and less than 5% on a file I/O intensive system (measured using batches of tar). == Usage == === Collecting trace data === Data collection is Started by: trace 15 foo This command will cause the LTT tracedaemon to do a trace that lasts for 15 seconds, writing trace data to foo.trace and process information from the /proc filesystem to foo.proc. The trace command is actually a script which runs the program tracedaemon with some common options. It is possible to run tracedaemon directly and in that case, the user can use a number of command-line options to control the data which is collected. For the complete list of options supported by tracedaemon, see the online manual page for tracedaemon. === Viewing the results === Viewing the results of a trace can be accomplished with: traceview foo This command will launch a graphical (GTK+) traceview tool that will read from foo.trace and foo.proc. This tool can show information in various interesting ways, including Event Graph, Process Analysis, and Raw Trace. The Event Graph is perhaps the most interesting view, showing the exact timing of events like page faults, interrupts, and context switches, in a simple graphical way. The traceview command is a wrapper for a program called tracevisualizer. For the complete list of options supported by tracevisualizer, see the online manual page for tracevisualizer.